Klarna
The FLX10-3S80 Flux ESC is the perfect match for the MM-3660-BL 3300KV 1/10th scale brushless motor - it's able to pump up to 80 amps of power to the motor for amazing stunts, colossal top speeds, and wheel-spinning sideways action!
Complete waterproof protection means you can take your truck equipped with the FLX10-3S80 ESC into territory that would scare off other drivers: puddles, mud, and more! A large fan sits on top of the case inside a protective cover to keep things cool when the weather's warm and you've been driving hard.
Technical Specifications:
Input Voltage: 2-3S LiPo
Continuous Current: 80A
Burst Current: 540A
Motor Limit: 2S LiPo <600KV, 3S <400KV
BEC: 6V Switching BEC, 2A Continuous Current
Battery Connector: T-Plug
Motor Connector: 4.0mm Bullet
Dimensions: 50.5x56.2x35.4m (W/Fan)
Application: 1/10th Buggy/Monster Truck
The FLX10-3S80 ESC & MM-3660-BL 3300KV Motor requires very powerful batteries to get the most out of them - please make sure that you use the right combination! HPI highly recommend the use of high quality LiPo batteries. Using batteries with low ratings, or the use of lower quality LiPo batteries, may cause damage to your batteries and/or speed control. Using batteries below the specified ratings may void the warranty of the speed controller and/or batteries.
NOTE: Before driving in wet conditions, make sure that other electronics fitted to the vehicle are safe to use (marked as water-resistant or waterproof), or that they are fully enclosed and protected from water and moisture (such as in a sealed receiver/battery case). Fans mounted on speed controllers are not water resistant - we recommend to disconnect the fan from the ESC before driving in wet conditions and allow it to dry fully before reconnecting the fan power. Lubricate exposed metal drivetrain parts such as bearings, outdrives and diff shafts before driving in wet conditions. Motors are not intended for submerged use and may be damaged if used when under water. After driving in wet conditions, make sure to rinse off dirt and any corrosive liquids like saltwater with plain water and re-lubricate metal drivetrain parts.
Snabba leveranser
Teknisk support
Säker betalning
Referens: 101103
Front Steering Fixing Parts Skruvar och distanser styrning
Referens: VP99352
Li Po Batteri 3s 11,1v 4500mah hårt paketT Kontackt.
Referens: 105895
These Shaped Exhaust Gaskets are genuine factory parts for HPI Savage X trucks. They are stock replacement parts for the Savage X4.6 and can be used on all Savage X engines if you're looking for a black gasket instead of the stock purple gasket. Sold in packs of 2.
The FLX10-3S80 Flux ESC is the perfect match for the MM-3660-BL 3300KV 1/10th scale brushless motor - it's able to pump up to 80 amps of power to the motor for amazing stunts, colossal top speeds, and wheel-spinning sideways action!
Complete waterproof protection means you can take your truck equipped with the FLX10-3S80 ESC into territory that would scare off other drivers: puddles, mud, and more! A large fan sits on top of the case inside a protective cover to keep things cool when the weather's warm and you've been driving hard.
Technical Specifications:
Input Voltage: 2-3S LiPo
Continuous Current: 80A
Burst Current: 540A
Motor Limit: 2S LiPo <600KV, 3S <400KV
BEC: 6V Switching BEC, 2A Continuous Current
Battery Connector: T-Plug
Motor Connector: 4.0mm Bullet
Dimensions: 50.5x56.2x35.4m (W/Fan)
Application: 1/10th Buggy/Monster Truck
The FLX10-3S80 ESC & MM-3660-BL 3300KV Motor requires very powerful batteries to get the most out of them - please make sure that you use the right combination! HPI highly recommend the use of high quality LiPo batteries. Using batteries with low ratings, or the use of lower quality LiPo batteries, may cause damage to your batteries and/or speed control. Using batteries below the specified ratings may void the warranty of the speed controller and/or batteries.
NOTE: Before driving in wet conditions, make sure that other electronics fitted to the vehicle are safe to use (marked as water-resistant or waterproof), or that they are fully enclosed and protected from water and moisture (such as in a sealed receiver/battery case). Fans mounted on speed controllers are not water resistant - we recommend to disconnect the fan from the ESC before driving in wet conditions and allow it to dry fully before reconnecting the fan power. Lubricate exposed metal drivetrain parts such as bearings, outdrives and diff shafts before driving in wet conditions. Motors are not intended for submerged use and may be damaged if used when under water. After driving in wet conditions, make sure to rinse off dirt and any corrosive liquids like saltwater with plain water and re-lubricate metal drivetrain parts.
